鋼結構門式鋼架設計計算書(鋼結構門架結構圖)

伊犁哈薩克自治州鋼結構設計 3周前 ( 11-23 06:32 ) 6364 搶沙發

今天給各位分享鋼結構門式鋼架設計計算書的知識，其中也會對鋼結構門架結構圖進行解釋,，如果能碰巧解決你現在面臨的問題,，別忘了關注本站，現在開始吧,！

今天給各位分享鋼結構門式鋼架設計計算書的知識,，其中也會對鋼結構門架結構圖進行解釋,，如果能碰巧解決你現在面臨的問題，別忘了關注本站,，現在開始吧,！

本文目錄一覽：

1、求專業人士翻譯
2,、pkpm鋼結構門式剛架的計算步驟（10版的），給的條件是廠房平面圖,，正側立面圖,，其他啥也沒給怎么算
3、鋼結構輕型門式剛架的問題

求專業人士翻譯

This works for light single-span steel structure portal frame design. Under the graduation requirements of the mission statement, the two sub-architecture design and structure. Part of the building, through the access to "design of steel structures GB50017-2003 ","Condensed Steel Design Manual ", and other relevant information, the door frame of 16 specimens of plant design, the distance between the two specimens of 6m, the total construction area of 1890m2 . The single portal frame structure is lightweight welded H beam (fixed section) as the main load-bearing skeleton, with cold-formed steel (C type) do purlins, wall beam; the pressure plate to do roofing, wall; use 80mm glass wool as insulation material and a light set appropriately supported housing structure system. Structural elements, has been formed under the requirements of building plans and inspect the "structures load code GB50009-2001 ","cold-formed steel structure technical specifications GB50018-2002 ","Steel Connections Design Manual"," Housing Architectural Design of Steel Structures "and other relevant norms and a certain amount of practical engineering design, for each frame of the most unfavorable loading Pin calculated using PKPM software to complete a reasonable cross section frame, and then the related design requirements, just Frame beams, columns, bracing, purlins and other components for stability calculations, draw, respectively, with AUTOCAD2008 design. Finally, the order book and the map calculated

pkpm鋼結構門式剛架的計算步驟（10版的）,，給的條件是廠房平面圖,，正側立面圖，其他啥也沒給怎么算

PKPM鋼結構模塊進入鋼結構門式鋼架設計計算書,，選門式鋼架二維設計鋼結構門式鋼架設計計算書,，新建文件鋼結構門式鋼架設計計算書，然后點左上角快速建模,，根據立面圖確定剛架檐口高度,，如有吊車應根據吊車起吊高度和吊車參數確定牛腿高度，根據平面圖確定受荷面積,，然后查荷載規范輸入恒載,、活載、風載,、吊車荷載等,，設置好參數然后點結構計算，查看計算結果超限了返回調整梁柱截面再計算,，最后進入施工圖繪制階段,，大概步驟如此，希望能對鋼結構門式鋼架設計計算書你有用